Is it bad to clean my skateboard bearings?

If you continue to ride very dirty or un-lubricated bearings, you run the risk of permanently damaging them and/or yourself. If this happens to your bearings, the skateboard will stop abruptly, causing you to fall and be injured. So keep them clean, dry and lubricated with Speed Cream.

Does WD40 ruin skateboard bearings?

You should never use WD40 to clean skateboard bearings . This is a product designed specifically made for removing rust and grime, not as a lubricant or cleaner for bearings.

Can you use soap and water to clean skateboard bearings?

Once all shields are off, they should be placed in a bowl of warm water and dish soap. Do not place the shields in acetone/solvent. Solvent will dry out and destroy the rubber/nylon compound of the shields that helps keep dirt out. With your fingers, simply rub the dirt and grease off with the soapy water.

Does rubbing alcohol clean skateboard bearings?

After you’ve let your skateboard bearings soak in the cup of isopropyl alcohol for at least 30 mins, take each bearing out individually and use a paper towel to wipe them clean and dry. Lastly, hit up some friends to skate and enjoy your clean bearings!

Can you use rubbing alcohol to clean skateboard bearings?

Now that the best and worst parts are over, it’s time to reap the benefits of your labor. After you’ve let your skateboard bearings soak in the cup of isopropyl alcohol for at least 30 mins, take each bearing out individually and use a paper towel to wipe them clean and dry.

Can I clean bearings with lemon juice?

If you can find a spray-on degreaser, you can blast all the crap out of your bearings to great effect. Lemon juice works well too! Soak your bearings in your chosen liquid try putting the bearings in a jam jar and shake the bejeezus out of them for about 2 minutes, then rinse them with some more clean solvent.

Can you clean skateboard bearings with vinegar?

No, I would recommend using acetone for the maintenance and cleaning of skateboard bearings. Vinegar and other citrus based cleaners do somewhat work but are prone to leave a slight greasy film afterwards.

Can I soak my bearings in rubbing alcohol?

Soak bearings in isopropyl alcohol With the bearings completely relieved of their shields, place each bearing in the cup and let the alcohol work its magic. You will want to leave them in there for a minimum of 30 mins with occasional swishing and swirling of the bearings.

Can you use Vaseline as lube for bearings?

When it comes to bearing, only use petroleum jelly for emergency fixes. However, if the metal temperature of the bearing will not get to the melting point of petroleum jelly, Vaseline should work fine. The other shortcoming of using petroleum jelly as a lubricant on the bearings is the cost.

Can you clean skateboard bearings with rubbing alcohol?

Put the bearings in a container WITH A LID and fill it to the brim with isopropyl alcohol. Cap the container and shake for 5 minutes. Set the bearings out to dry. While you’re waiting for the alcohol to fully evaporate, you can take the time to clean the bearing covers with some paper towels.

What is the best way to clean skateboard bearings?

Acetone , isopropyl alcohol and mineral spirits are all good options. When using solvents, wear gloves and avoid contact with your skin. Use a dish or wide-mouthed bottle as a container to soak the bearings for several minutes, occasionally swirling the bearings around in the cleaner.

How often should I Clean my skateboard bearings?

Remember, bearings only need to be cleaned about once every two to three months depending on the environment you are skating in. If you primarily skate inside several times a month but the surface is not cleaned often, you might have to shine up your bearings once a month.

What are some ways to grease skateboard bearings?

Necessary Items

Pulling Apart. Disassemble the dirty bearings from your skateboard wheel.

Cleaning. Pour some acetone in your bowl and submerge the bearings in it.

Greasing. Add 2-3 drops of grease in between the balls.

Reassembly. Reassemble the skate wheel with the freshly lubed bearing.

What do you clean skate bearings with?

Shake the bottle for two minutes, or until all the dirt has been removed from your bearings. You can also use a citrus based cleaner with an orange oil or lemon juice to clean your bearings. Dry your bearings with a hairdryer. Remove the bearings from the solvent and place them on a dry paper towel or rag.